Support for automatic switch between WiFi and 3G (only for GV-VS12 and GV-VS14)
Support for temperature detector (only for GV-VS14)
Support for the UMTS module of Huawei E1756C (only for GV-VS11, GV-VS12 and GV-VS14)
Fixed:
Failure of schedule recording after proceeding from span 1 (set as Round the clock) to span 2 (set as Motion)
Possible system failure when using CGI command to obtain a snapshot of live view
Inability of N/C output devices to function properly after system reboot
Incorrect frame rate after changing video signal format (only for GV-VS11)
Possible system failure when video lost occurred with dual streaming enabled (only for GV-VS14)
Modified:
Maximum streams allowed for connecting with the GV-Video Server changed from 20 to 8 (GV-VS04H), 16 (GV-VS14), and 4 (GV-VS11 and GV-VS12)
Improved:
Recording efficiency and stability in which the recorded files remain accessible when power is disrupted during monitoring
Video Server (GV-VS04H) Version History:
Firmware V1.08 2013-10-04
New:
Support for automatic switch between WiFi and 3G (only for GV-VS12 and GV-VS14)
Support for temperature detector (only for GV-VS14)
Support for the UMTS module of Huawei E1756C (only for GV-VS11, GV-VS12 and GV-VS14)
Fixed:
Failure of schedule recording after proceeding from span 1 (set as Round the clock) to span 2 (set as Motion)
Possible system failure when using CGI command to obtain a snapshot of live view
Inability of N/C output devices to function properly after system reboot
Incorrect frame rate after changing video signal format (only for GV-VS11)
Possible system failure when video lost occurred with dual streaming enabled (only for GV-VS14)
Modified:
Maximum streams allowed for connecting with the GV-Video Server changed from 20 to 8 (GV-VS04H), 16 (GV-VS14), and 4 (GV-VS11 and GV-VS12)
Improved:
Recording efficiency and stability in which the recorded files remain accessible when power is disrupted during monitoring
Firmware V1.07 2012-11-08
Fixed:
Incorrect system date after rebooting system at the last day of certain months
Firmware V1.06 2012-08-29
New:
Support for GPS time synchronization (only for GV-VS04H and GV-VS12)
Support for DNS setting for UMTS
Support for language change from the Web interface
Support for Edimax 7711UAn WiFi adapter
Support for the following UMTS modules:
- Huawei EC189
- Huawei EC353, E303 (only for GV-VS04H and GV-VS12)
- Bandluxe C320, C501 (only for GV-VS04H and GV-VS12)
Fixed:
Unstable connection with GV-Backup Center
Possible failure of sending notification messages to GV-Center V2 server or VSM server
Partially incorrect language display on Windows 7 of Serbian version
Failure of detecting vehicle speed with the west longitude (only for GV-VS04H and GV-VS12)
Modified:
Default network connection in which the previous connection mode, static IP connection with default IP address 192.168.0.10 is now changed to DHCP connection
Improved:
RTSP authentication with which users can disable the ID and password request when accessing the live view through RTSP
Firmware V1.05 2012-01-11
New:
Support for new PTZ cameras: AcutVista SSD-7971D and DynaColor DynaHawk Zh701
"Cease video lost messages from" option added to the Center V2 / VSM setting pages to stop notifying Center V2 / VSM of video lost messages from the selected camera
"Start Record" and "Stop Record" options added to the Output setting page to automatically activate the assigned output device when recording is started and stopped
Fixed:
System restart issue after disconnecting to the network for about 40 minutes
Failure to record videos for whole day when the Weekend option was enabled on Recording Schedule
Remote ViewLog failure that occurred when playing the damaged video files
System restart issue when UPnP was enabled
Failure to display images when the COP (15-CD55W) Pelco D PTZ camera was connected
Failure to verify watermark of the recordings with the H.264 codec. The problem only occurred on GV-VS04H.
Distortion of recorded images that occurred with the settings of MJPEG codec and half D1 resolution. The problem only occurred on GV-VS12.
Failure to display images when connecting to GV-System through RTSP and with D1 or half D1 resolution. The problem only occurred on GV-VS12.
Firmware V1.03 2011-01-17
New:
Auto Reboot Setup function
Repair Record Database function
Support for connection with up to two GV-Center V2 / GV-VSM / GV-Video Gateway simultaneously
Support for CGI command function for obtaining a snapshot of the camera view without logging in the Web interface
Support for audio streaming using RTSP protocol
Support for more mobile broadband devices: Huawei E1752, E1756; Novatel MC996D, MC998D; ONDA MSA523HS
The OCX registration path on the Web interface updated to OCX 8400
Fixed:
Failure of message transmission to GV-Center V2 and VSM when a hard disk error is detected or when the hard disk is full
Issue of recording on all cameras simultaneously upon input trigger
Issue of recycling events when the Enable Recycling option is selected
Issue of video recording interruption
Failure of executing recording schedule if the GV-Video Server is rebooted after recording schedule has been started
Failure of recycling events when Keep Days are specified
Issue of displaying only local IP address in the e-mail when using UMTS
Failure of sending captured live images upon input trigger when e-mail and FTP alerts are both enabled
Failure of I/O schedule recording when the input is triggered before and continued into the specified starting time of the I/O schedule
Failure of recycling events after system reboot with the available hard drive space less than the specified stop-recording-and-recycle threshold.
Failure of sending the e-mail alerts to all the recipients on Motion Detection mode
Incorrect time synchronization with the computer
Issue of exceeding number of frames (9300 fps) when recording
Modified:
Image quality options which is changed from 3 options (Fair, Good and Excellent) to 5 options (Poor, Fair, Good, Great and Excellent)
The video resolution is modified from 720 x 480 (720 x 576) to 704 x 480 (704 x 576) and from 360 x 240 (360 x 288) to 352 x 240 (352 x 288)
The System Log in the Log Information section renamed to "Debug Messages"
3GPP section which is renamed to "RTSP / 3GPP"
The amount of GPS data transferred in which unnecessary parts are deleted to reduce data size
GV-VS04A (4Ch MPEG4 Video Server) Version History
Firmware V1.02 2010-07-26
New:
GV-Backup Center connection
Support for RTSP protocol
Support for mobile broadband devices: Vodafone K3565 (Rev 2) and Huawei EC169C CDMA2000 3G Modem
Support for the wireless USB adaptor: Pegatron WL-166N11
Fixed:
Connection issue with the GV-Video Gateway after the GV-Video Server was restarted
Incorrect connection time with the GV-Video Gateway
Failure to update IP address to DynDNS after network was broken or the GV-Video Server was restarted
Issue of incorrect Daylight Saving Time
Recording issue that occurred after the storage device was removed during recording process
Recording issue that occurred after the Live View was closed and then opened again
Database issue that caused the GV-Video Server to restart
Issue of motion detection recording after the GV-Video Server was restarted
Failure to control the PTZ camera after its baud rate was set to be 2400
Issue of audio recording which was activated with I/O monitoring even though you did not enable audio recording
Modified:
"Video Lost" message now displayed on the Live View window once the camera is disconnected
Schedule settings now available on the UMTS Settings page for automatic mobile broadband connection
Update time of Network Time Server now definable
Stability of UMTS connection
Firmware V1.01 2010-05-03
New:
Support for wireless modules, Pegatron WL-166N11 and Edimax EW-7711UMn (Version 3.0)
Fixed:
Incorrect MAC Address displayed on the Web interface when PPPoE connection is in use
System failure that was caused by power outage during system restart
Issue of recycling events
Failure of password protection for multicasting streams
Problem of IE crash when you used PIP/PAP function on Windows 7
Failure of the Buzzer and E-mail alerts on incorrect hard disk status
Inconsistent message of storage space displayed on the GV-Video Server’s Web interface and VSM.
Lag issue of live view that occurred when no hard drive was set up in the GV-Video Server
Incorrect message time on System Log
Failure to update IP address to DynDNS if network has been broken or the GV-Video Server has been restarted
Video Server (GV-VS04A & GV-VS04H) Version History:
Firmware V1.06 2013-10-04
New:
Support for automatic switch between WiFi and 3G (only for GV-VS12 and GV-VS14)
Support for temperature detector (only for GV-VS14)
Support for the UMTS module of Huawei E1756C (only for GV-VS11, GV-VS12 and GV-VS14)
Fixed:
Failure of schedule recording after proceeding from span 1 (set as Round the clock) to span 2 (set as Motion)
Possible system failure when using CGI command to obtain a snapshot of live view
Inability of N/C output devices to function properly after system reboot
Incorrect frame rate after changing video signal format (only for GV-VS11)
Possible system failure when video lost occurred with dual streaming enabled (only for GV-VS14)
Modified:
Maximum streams allowed for connecting with the GV-Video Server changed from 20 to 8 (GV-VS04H), 16 (GV-VS14), and 4 (GV-VS11 and GV-VS12)
Improved:
Recording efficiency and stability in which the recorded files remain accessible when power is disrupted during monitoring
Firmware V1.05 2012-01-11
New:
Support for new PTZ cameras: AcutVista SSD-7971D and DynaColor DynaHawk Zh701
"Cease video lost messages from" option added to the Center V2 / VSM setting pages to stop notifying Center V2 / VSM of video lost messages from the selected camera
"Start Record" and "Stop Record" options added to the Output setting page to automatically activate the assigned output device when recording is started and stopped
Fixed:
System restart issue after disconnecting to the network for about 40 minutes
Failure to record videos for whole day when the Weekend option was enabled on Recording Schedule
Remote ViewLog failure that occurred when playing the damaged video files
System restart issue when UPnP was enabled
Failure to display images when the COP (15-CD55W) Pelco D PTZ camera was connected
Failure to verify watermark of the recordings with the H.264 codec. The problem only occurred on GV-VS04H.
Distortion of recorded images that occurred with the settings of MJPEG codec and half D1 resolution. The problem only occurred on GV-VS12.
Failure to display images when connecting to GV-System through RTSP and with D1 or half D1 resolution. The problem only occurred on GV-VS12.
Firmware V1.03 2011-01-17
New:
Auto Reboot Setup function
Repair Record Database function
Support for connection with up to two GV-Center V2 / GV-VSM / GV-Video Gateway simultaneously
Support for CGI command function for obtaining a snapshot of the camera view without logging in the Web interface
Support for audio streaming using RTSP protocol
Support for more mobile broadband devices: Huawei E1752, E1756; Novatel MC996D, MC998D; ONDA MSA523HS
The OCX registration path on the Web interface updated to OCX 8400
Fixed:
Failure of message transmission to GV-Center V2 and VSM when a hard disk error is detected or when the hard disk is full
Issue of recording on all cameras simultaneously upon input trigger
Issue of recycling events when the Enable Recycling option is selected
Issue of video recording interruption
Failure of executing recording schedule if the GV-Video Server is rebooted after recording schedule has been started
Failure of recycling events when Keep Days are specified
Issue of displaying only local IP address in the e-mail when using UMTS
Failure of sending captured live images upon input trigger when e-mail and FTP alerts are both enabled
Failure of I/O schedule recording when the input is triggered before and continued into the specified starting time of the I/O schedule
Failure of recycling events after system reboot with the available hard drive space less than the specified stop-recording-and-recycle threshold.
Failure of sending the e-mail alerts to all the recipients on Motion Detection mode
Incorrect time synchronization with the computer
Issue of exceeding number of frames (9300 fps) when recording
Modified:
Image quality options which is changed from 3 options (Fair, Good and Excellent) to 5 options (Poor, Fair, Good, Great and Excellent)
The video resolution is modified from 720 x 480 (720 x 576) to 704 x 480 (704 x 576) and from 360 x 240 (360 x 288) to 352 x 240 (352 x 288)
The System Log in the Log Information section renamed to "Debug Messages"
3GPP section which is renamed to "RTSP / 3GPP"
The amount of GPS data transferred in which unnecessary parts are deleted to reduce data size
GV-VS04A (4Ch MPEG4 Video Server) Version History
Firmware V1.02 2010-07-26
New:
GV-Backup Center connection
Support for RTSP protocol
Support for mobile broadband devices: Vodafone K3565 (Rev 2) and Huawei EC169C CDMA2000 3G Modem
Support for the wireless USB adaptor: Pegatron WL-166N11
Fixed:
Connection issue with the GV-Video Gateway after the GV-Video Server was restarted
Incorrect connection time with the GV-Video Gateway
Failure to update IP address to DynDNS after network was broken or the GV-Video Server was restarted
Issue of incorrect Daylight Saving Time
Recording issue that occurred after the storage device was removed during recording process
Recording issue that occurred after the Live View was closed and then opened again
Database issue that caused the GV-Video Server to restart
Issue of motion detection recording after the GV-Video Server was restarted
Failure to control the PTZ camera after its baud rate was set to be 2400
Issue of audio recording which was activated with I/O monitoring even though you did not enable audio recording
Modified:
"Video Lost" message now displayed on the Live View window once the camera is disconnected
Schedule settings now available on the UMTS Settings page for automatic mobile broadband connection
Update time of Network Time Server now definable
Stability of UMTS connection
Firmware V1.01 2010-05-03
New:
Support for wireless modules, Pegatron WL-166N11 and Edimax EW-7711UMn (Version 3.0)
Fixed:
Incorrect MAC Address displayed on the Web interface when PPPoE connection is in use
System failure that was caused by power outage during system restart
Issue of recycling events
Failure of password protection for multicasting streams
Problem of IE crash when you used PIP/PAP function on Windows 7
Failure of the Buzzer and E-mail alerts on incorrect hard disk status
Inconsistent message of storage space displayed on the GV-Video Server’s Web interface and VSM.
Lag issue of live view that occurred when no hard drive was set up in the GV-Video Server
Incorrect message time on System Log
Failure to update IP address to DynDNS if network has been broken or the GV-Video Server has been restarted
GV-H.264 Video Server VS12 Version History
Firmware V1.07 2013-10-04
New:
Support for automatic switch between WiFi and 3G (only for GV-VS12 and GV-VS14)
Support for temperature detector (only for GV-VS14)
Support for the UMTS module of Huawei E1756C (only for GV-VS11, GV-VS12 and GV-VS14)
Fixed:
Failure of schedule recording after proceeding from span 1 (set as Round the clock) to span 2 (set as Motion)
Possible system failure when using CGI command to obtain a snapshot of live view
Inability of N/C output devices to function properly after system reboot
Incorrect frame rate after changing video signal format (only for GV-VS11)
Possible system failure when video lost occurred with dual streaming enabled (only for GV-VS14)
Modified:
Maximum streams allowed for connecting with the GV-Video Server changed from 20 to 8 (GV-VS04H), 16 (GV-VS14), and 4 (GV-VS11 and GV-VS12)
Improved:
Recording efficiency and stability in which the recorded files remain accessible when power is disrupted during monitoring
Firmware V1.06 2012-08-14
New:
Support for GPS time synchronization (only for GV-VS04H and GV-VS12)
Support for DNS setting for UMTS
Support for language change from the Web interface
Support for Edimax 7711UAn WiFi adapter
Support for the following UMTS modules:
- Huawei EC189
- Huawei EC353, E303 (only for GV-VS04H and GV-VS12)
- Bandluxe C320, C501 (only for GV-VS04H and GV-VS12)
Fixed:
Unstable connection with GV-Backup Center
Possible failure of sending notification messages to GV-Center V2 server or VSM server
Partially incorrect language display on Windows 7 of Serbian version
Failure of detecting vehicle speed with the west longitude (only for GV-VS04H and GV-VS12)
Modified:
Default network connection in which the previous connection mode, static IP connection with default IP address 192.168.0.10 is now changed to DHCP connection
Improved:
RTSP authentication with which users can disable the ID and password request when accessing the live view through RTSP
Firmware V1.05 2011-12-30
New:
Support for new PTZ cameras: AcutVista SSD-7971D and DynaColor DynaHawk Zh701
"Cease video lost messages from" option added to the Center V2 / VSM setting pages to stop notifying Center V2 / VSM of video lost messages from the selected camera
"Start Record" and "Stop Record" options added to the Output setting page to automatically activate the assigned output device when recording is started and stopped
Fixed:
System restart issue after disconnecting to the network for about 40 minutes
Failure to record videos for whole day when the Weekend option was enabled on Recording Schedule
Remote ViewLog failure that occurred when playing the damaged video files
System restart issue when UPnP was enabled
Failure to display images when the COP (15-CD55W) Pelco D PTZ camera was connected
Failure to verify watermark of the recordings with the H.264 codec. The problem only occurred on GV-VS04H.
Distortion of recorded images that occurred with the settings of MJPEG codec and half D1 resolution. The problem only occurred on GV-VS12.
Failure to display images when connecting to GV-System through RTSP and with D1 or half D1 resolution. The problem only occurred on GV-VS12.
Firmware V1.04 2011-01-14
New:
Auto Reboot Setup function
Repair Record Database function
Support for connection with up to two GV-Center V2 / GV-VSM / GV-Video Gateway simultaneously
Support for CGI command function for obtaining a snapshot of the camera view without logging in the Web interface
Support for audio streaming using RTSP protocol
Support for more mobile broadband devices: Huawei E1752, E1756; Novatel MC996D, MC998D; ONDA MSA523HS
The OCX registration path on the Web interface updated to OCX 8400
Fixed:
Failure of message transmission to GV-Center V2 and VSM when a hard disk error is detected or when the hard disk is full
Issue of recording on all cameras simultaneously upon input trigger
Issue of recycling events when the Enable Recycling option is selected
Issue of video recording interruption
Failure of executing recording schedule if the GV-Video Server is rebooted after recording schedule has been started
Failure of recycling events when Keep Days are specified
Issue of displaying only local IP address in the e-mail when using UMTS
Failure of sending captured live images upon input trigger when e-mail and FTP alerts are both enabled
Failure of I/O schedule recording when the input is triggered before and continued into the specified starting time of the I/O schedule
Failure of recycling events after system reboot with the available hard drive space less than the specified stop-recording-and-recycle threshold.
Failure of sending the e-mail alerts to all the recipients on Motion Detection mode
Incorrect time synchronization with the computer
Issue of exceeding number of frames (9300 fps) when recording
Issue of audio delay
Modified:
Image quality options which is changed from 3 options (Fair, Good and Excellent) to 5 options (Poor, Fair, Good, Great and Excellent)
The video resolution is modified from 720 x 480 (720 x 576) to 704 x 480 (704 x 576) and from 360 x 240 (360 x 288) to 352 x 240 (352 x 288)
The System Log in the Log Information section renamed to "Debug Messages"
3GPP section which is renamed to "RTSP / 3GPP"
The amount of GPS data transferred in which unnecessary parts are deleted to reduce data size
Firmware V1.03 2010-07-26
New:
GV-Backup Center connection
Support for RTSP protocol
Support for mobile broadband devices: Vodafone K3565 (Rev 2) and Huawei EC169C CDMA2000 3G Modem
Support for the wireless USB adaptor: Pegatron WL-166N11
Fixed:
Connection issue with the GV-Video Gateway after the GV-Video Server was restarted
Incorrect connection time with the GV-Video Gateway
Failure to update IP address to DynDNS after network was broken or the GV-Video Server was restarted
Issue of incorrect Daylight Saving Time
Recording issue that occurred after the storage device was removed during recording process
Recording issue that occurred after the Live View was closed and then opened again
Database issue that caused the GV-Video Server to restart
Issue of motion detection recording after the GV-Video Server was restarted
Failure to control the PTZ camera after its baud rate was set to be 2400
Issue of audio recording which was activated with I/O monitoring even though you did not enable audio recording
Modified:
"Video Lost" message now displayed on the Live View window once the camera is disconnected
Schedule settings now available on the UMTS Settings page for automatic mobile broadband connection
Update time of Network Time Server now definable
Stability of UMTS connection
Firmware V1.02 2010-03-12
New:
Multicast and Audio Broadcast
Watermark
Text Overlay
System Log
GV-Video Gateway connection
Connections to 2 GV-GIS stations
Support for new mobile broadband devices: Huawei E1692 and E1750, Novatel MC950D, Verizon USB760
Support for wireless modules complied with 802.11n standard: Linksys WUSB600, D-Link DWA-140 (H/W version B1) and Edimax EW-7718Un
Fixed:
Failure to disable the admin privilege for FTP Server
An error message that occurred after the "Disable authentication for guest account" option was applied on the User Account setting
Issue of repairing corrupted AVI files
Incorrect GPS Baud Rate setting
Malfunction of Ready LED that was caused by power outage during system restart
Login failure that occurred when there were many connection requests and automatic retry did not work
Issue of black images that occurred after you modified the video attribute of GV-Video Server and then selected Default from GV-System
Issue of recycling events
Issue of updating OCX program
Problem of achieving the defined FPS that occurred if you plugged the network cable after GV-Video Server had been started
Failure to switch to the wired LAN connection after disabling the wireless connection
Connection problem with Verizon Wireless USB727 Modem (EVDO)
Issue of saving Daylight Saving Time settings after GV-Video Server was restarted
Failure of Visual Automation
Incorrect output trigger during system restart that occurred only when GV-Relay V2 was connected
Problem of using the Virtual I/O function in Pulse Mode on GV-System with GV-Video Server
Incorrect MAC Address that appeared on the Web interface when using PPPoE connection
Modified:
Shortened the time of firmware upgrade from 13 minutes to 4 minutes
Firmware V1.01 2009-08-06
New:
Support for wireless modules complied with 802.11n standard, including Linksys WUSB600, D-Link DWA-140 (H/W version B1) and Edimax EW-7718Un
Fixed:
Problem of output devices, attached to GV-VS12, failing to be remotely triggered by the VSM users.
Failure of the Microphone function.
Problem of drawn motion detection areas that were relocated when the codec was changed from MJPEG to H.264 or MPEG4
Problem of displaying live images when using the computer with single-core CPU.
Failure of the Tampering Alarm function that occurred when only one camera was functioning
Error of password requirement for Guest users after they were allowed to log in without passwords
Error of successfully logging in FTP Server with "admin" after the user name was changed.
Incorrect messages about input status.
Video Server (GV-VS11) Version History:
Firmware V1.03 2013-10-04
New:
Support for automatic switch between WiFi and 3G (only for GV-VS12 and GV-VS14)
Support for temperature detector (only for GV-VS14)
Support for the UMTS module of Huawei E1756C (only for GV-VS11, GV-VS12 and GV-VS14)
Fixed:
Failure of schedule recording after proceeding from span 1 (set as Round the clock) to span 2 (set as Motion)
Possible system failure when using CGI command to obtain a snapshot of live view
Inability of N/C output devices to function properly after system reboot
Incorrect frame rate after changing video signal format (only for GV-VS11)
Possible system failure when video lost occurred with dual streaming enabled (only for GV-VS14)
Modified:
Maximum streams allowed for connecting with the GV-Video Server changed from 20 to 8 (GV-VS04H), 16 (GV-VS14), and 4 (GV-VS11 and GV-VS12)
Improved:
Recording efficiency and stability in which the recorded files remain accessible when power is disrupted during monitoring
Firmware V1.02 2012-09-04
New:
Support for GPS time synchronization (only for GV-VS04H and GV-VS12)
Support for DNS setting for UMTS
Support for language change from the Web interface
Support for Edimax 7711UAn WiFi adapter
Support for the following UMTS modules:
- Huawei EC189
- Huawei EC353, E303 (only for GV-VS04H and GV-VS12)
- Bandluxe C320, C501 (only for GV-VS04H and GV-VS12)
Fixed:
Unstable connection with GV-Backup Center
Possible failure of sending notification messages to GV-Center V2 server or VSM server
Partially incorrect language display on Windows 7 of Serbian version
Failure of detecting vehicle speed with the west longitude (only for GV-VS04H and GV-VS12)
Modified:
Default network connection in which the previous connection mode, static IP connection with default IP address 192.168.0.10 is now changed to DHCP connection
Improved:
RTSP authentication with which users can disable the ID and password request when accessing the live view through RTSP
Video Server (GV-VS02) Version History:
Firmware V1.49 2010-03-08
Fixed:
Lag issue that occurred when no storage device was connected to the GV-Video Server
Failure of playing video through Remote ViewLog when you clicked several events from the Event List at one time
Failure of playing video through Remote ViewLog in Quad View mode
Firmware V1.48 2009-12-01
Bug fixed:
Problem of disconnecting from Control Center or GV-GIS through wireless broadband access
Problem of using the USB flash drive
Incorrect output status that occurred once the GV-Video Server was connected to the GV-System in Pulse mode
Incorrect time length for Pulse mode that occurred once the GV-Video Server was connected to the GV-System
Incorrect display of camera status on the Monitoring page after video was lost
Failure of Wiegand function after the GV-Video Server was rebooted
Automatic retry issue
Lag issue for the video with lower bit rate
Issue of the output triggered by motion detection
Failure of audio function after you hided the selection menu on the left side of the Live View
Issue of downloading OCX on Internet Explore 8
Firmware V1.46 2009-02-11
New:
The Disk Full / Fault LED flickering every 5 seconds when GV-Video Server is recoding
Multicast and Audio Broadcast
Remote control of I/O devices allowed from GV-System V8.3
GPS data to be resent after the connection to GV-GIS is rebuilt
Support for Verizon Wireless USB727 Modem
Fixed:
Incorrect longitude and latitude values displayed during GPS tracking
Failure of rebooting the GV-Video Server on the web setting page.
Failure of setting alert interval time on both E-Mail and FTP setting pages
Failure of the PTZ Preset function when input devices were triggered
Firmware V1.45 2008-10-21
New:
Support for Geo-GIS (Geographic Information System)
Support for a new UMTS module: GlobeSurfer iCON7.2
Uploading of snapshot images in the sequence to FTP Server upon trigger events
Resolution options for snapshots added to E-Mail and FTP alert settings
“1 frame per second” option added to video settings
“Baud Rate” option added to GPS settings
Additional input device included for triggering the operations of “Start monitoring” and “Stop monitoring”
Support for the playback of files recorded during Daylight Saving Time period with ViewLog player of version 8.3
Fixed:
Failure of Panasonic PTZ function
Inconsistency between audio and video occurred when GV-NVR was in connection
Issues of Wiegand function that failed to send cardholder data to Center V2 and VSM, and the video server was rebooted
Incorrect time stamp on the image after the Time Zone setting was changed
Failure to send an e-mail to multiple recipients
Failure to send monitoring commands to Center V2 and VSM
An issue related to repair AVI files
Modified:
Settings for Video, Schedule, Time Synchronization, Input and Output to be protected when the monitoring is started.
Wired Ethernet connection to coexist with wireless Ethernet connection
“Overlaid with IO input name” option added to display the names of inputs on images
“Keep Check UMTS Connection” option added to enable the automatic connection check and retry
Fixed:
Error of audio recorded on Motion Detection mode despite that the “Record audio” option was already disabled
GPS function sent wrong information about longitude and latitude to the Geo-GIS program
Problem of resuming interrupted file transfer of files from GV-Video Server via Remote ViewLog
Incorrect time synchronization with the time server
Internal clock inaccuracy
Problem of motion detection that may not trigger FTP/e-mail alerts and recording
Issues of UMTS (Universal Mobile Telephone System) connection
Modified:
Resolution of snapshots for e-mail and FTP alerts to be determined by the resolution of Video Settings
Output Setting page by adding the “Enable” option
Default time setting to be “Synchronized with Network Time Server” instead of manually modifying the time
Preset value for GOP to be “2” instead of “1” when the network connection is set to be 3GPPv6 or 3GPPv7
Firmware V1.42 2008-03-13
New:
Support for multiple languages for Web interface: Thai / Hungarian / Russian / Serbian / Danish / Polish / German / Spanish / Czech / Japanese / Traditional Chinese / French / Portuguese / Italian / Hebrew / Simplified Chinese
Support for new UMTS device: Brandrich BandLuxe C100
A new option in “Input Settings” to send the image of desired camera(s) to Center V2 upon input trigger
A new option in “GPS Settings” to set update frequency between 1 and 30 seconds
Fixed:
Failure to format the HDD which is less than 200GB capacity
Problem of ViewLog Server that only allowed the maximum of 150 video files for playback
Compatibility issues between DDNS function and UMTS connection
Failure to modify input settings
Failure to save previous settings for Brightness, Contrast, Saturation and Hue after Video Server was restarted
Modified:
Changed defaults settings for 3GPPV6 and 3GPPV7. When you select 3GPPV7 as connection type, default values now are 1 for GOP and 7.5 (NTSC)/8 (PAL) for frame rate. When you select 3GPPV6, default values now are 1 for GOP and 5 (NTSC)/5 (PAL) for frame rate
Firmware V1.41 2008-02-13
Fixed:
Failure to send a captured still image by E-Mail or FTP
Failure to configure the Visual Automation function over Internet
Firmware V1.40 2008-02-01
New:
Support for Universal Mobile Telephone System (UMTS) technology
Support for GPS (only for Hardware Version 2.0)
"Apply the settings to all cameras" option added to Video Settings
Fixed:
Compatibility issues with Lilin domes, including preset and direction functions
Problem of narrowband connection being constantly broken
Wrong encoding of PTZ Control Panel in Hebrew edition
Error of continued recording after the scheduled time ends
Failure to reallocate DDNS IP address after rebooting
Modified:
Extended the duration of "Trigger Pulse Mode" in Output Setting to 60 seconds
Increased the number of characters entered in the FTP Remote Directory field to 30
Changed the format of pictures sent by FTP or SMTP to .JPG
Removed "Time Offset" option from Date and Time Setting
Disabled "Daylight Saving Time" option when time is set manually
Changed weekday settings in Recording Schedule to time frame (Span) settings for Monday to Sunday
Improved:
Support for On-Screen Display (OSD) when connected PTZ devices provide this function
Enhanced Live View functions and user interfaces
Firmware V1.31 2007-07-20
Modified:
Set output to default when monitoring mode (manual/schedule) stopped
Fixed:
Fixed when you set the image resolutions to 720 x 480 (NTSC) / 720 x 576 (PAL) or 720 x 480 De-interlaced (NTSC) / 720 x 576 De-interlaced (PAL), the following problem may occur on the GV-System of version 8.11 or earlier:
No image appears on Center V2 of version 8.11 or earlier when activating Center V2 monitoring for alarm events.
Green image appears when the Video Server connects to the GV-System of version 8.11 or earlier.
Green image appears when connecting to the Video Server for playback using the Remote ViewLog function of version 8.11 or earlier
Motion triggers output function must work in schedule-round the clock mode
Initial values for outputs are wrong after system rebooting
Input triggers output function failed in schedule mode
Time does not match in system and remote PC
Firmware V1.30 2007-07-05
New:
Added "Keep Day" function
PTZ camera directed to a preset point upon input trigger
Added Center V2 and VSM monitoring schedules
Added options to stop notifying Center V2 and VSM of alert events
Fixed:
Adjusted PAL image position on the screen
Fixed the audio callback issue caused by unstable connection
Fixed the image issue when the live view screen was overlapped by the dialog box of another application
Fixed the remote playback problem of Remote ViewLog caused by unstable connection
Fixed Lilin PTZ Dome problems
Changed:
Changed PTZ default setting to Pelco D
Changed logo for StorVision (OEM customized)
Modified:
Modify TW2804 registers for better video quality
Firmware V1.21 2007-03-02
New:
Add the "Monitoring Settings" page, featuring:
Manual recording
I/O monitoring by input trigger
Display of recording status
Add the "Remote ViewLog" link in the menu page
The camera can be assigned to start recording upon I/O and Wiegand devices trigger.
Support 13 languages.
Fixed:
Password error when it was set with 7 characters.
Connection lost to the server when live audio (Microphone feature) was enabled and then disabled.
Video Server (GV-VS02A) Version History:
Firmware V1.05 2011-01-14
New:
Auto Reboot Setup function
Repair Record Database function
Support for connection with up to two GV-Center V2 / GV-VSM / GV-Video Gateway simultaneously
Support for CGI command function for obtaining a snapshot of the camera view without logging in the Web interface
Support for audio streaming using RTSP protocol
Support for more mobile broadband devices: Huawei E1752, E1756; Novatel MC996D, MC998D; ONDA MSA523HS
The OCX registration path on the Web interface updated to OCX 8400
Fixed:
Failure of message transmission to GV-Center V2 and VSM when a hard disk error is detected or when the hard disk is full
Issue of recording on all cameras simultaneously upon input trigger
Issue of recycling events when the Enable Recycling option is selected
Issue of video recording interruption
Failure of executing recording schedule if the GV-Video Server is rebooted after recording schedule has been started
Failure of recycling events when Keep Days are specified
Issue of displaying only local IP address in the e-mail when using UMTS
Failure of sending captured live images upon input trigger when e-mail and FTP alerts are both enabled
Failure of I/O schedule recording when the input is triggered before and continued into the specified starting time of the I/O schedule
Failure of recycling events after system reboot with the available hard drive space less than the specified stop-recording-and-recycle threshold.
Failure of sending the e-mail alerts to all the recipients on Motion Detection mode
Incorrect time synchronization with the computer
Issue of exceeding number of frames (9300 fps) when recording
Modified:
Image quality options which is changed from 3 options (Fair, Good and Excellent) to 5 options (Poor, Fair, Good, Great and Excellent)
The video resolution is modified from 720 x 480 (720 x 576) to 704 x 480 (704 x 576) and from 360 x 240 (360 x 288) to 352 x 240 (352 x 288)
The System Log in the Log Information section renamed to "Debug Messages"
3GPP section which is renamed to "RTSP / 3GPP"
The amount of GPS data transferred in which unnecessary parts are deleted to reduce data size
Firmware V1.04 2010-07-26
Fixed:
Failure to display the PTZ panel.
Failure to play back videos recorded in the GV-Video Sever with the settings of CIF resolution
Firmware V1.03 2010-07-15
New:
GV-Backup Center connection
Support for RTSP protocol
Support for mobile broadband devices: Vodafone K3565 (Rev 2) and Huawei EC169C CDMA2000 3G Modem
Support for the wireless USB adaptor: Pegatron WL-166N11
Fixed:
Connection issue with the GV-Video Gateway after the GV-Video Server was restarted
Incorrect connection time with the GV-Video Gateway
Failure to update IP address to DynDNS after network was broken or the GV-Video Server was restarted
Issue of incorrect Daylight Saving Time
Recording issue that occurred after the storage device was removed during recording process
Recording issue that occurred after the Live View was closed and then opened again
Database issue that caused the GV-Video Server to restart
Issue of motion detection recording after the GV-Video Server was restarted
Failure to control the PTZ camera after its baud rate was set to be 2400
Issue of audio recording which was activated with I/O monitoring even though you did not enable audio recording
Modified:
"Video Lost" message now displayed on the Live View window once the camera is disconnected
Schedule settings now available on the UMTS Settings page for automatic mobile broadband connection
Update time of Network Time Server now definable
Stability of UMTS connection
Firmware V1.02 2010-03-18
Fixed:
Lag issue of live view that occurred when no hard drive was set up in the GV-Video Server
Incorrect MAC Address that appeared on the Web interface when using PPPoE connection
System failure that was caused by power outage during system restart
Issue of recycling events
Password issue of Multicast
Issue of using PIP and PAP functions on Windows 7
Issue of e-mail and buzzer alarms on recording error
Incorrect storage status displayed on VSM that occurred after the disk size was changed
Incorrect time display on System Log
Firmware V1.01 2009-11-18
New:
Video Channel Source Settings
Watermark
System Log
Text Overlay
Connections to 2 GIS stations
Video Gateway Connection
Backup Center Connection
Support for new mobile broadband devices: Huawei E169, E1692, E1750, and Novatel USB760
Support for wireless modules complied with 802.11n standard: Linksys WUSB600, D-Link DWA-140 (H/W version B1) and Edimax EW-7718Un
Fixed:
Problem of playing video clips on the Event List of Remote ViewLog when too many video clips were clicked at one time
Failure to import system settings by using GV IP Device Utility
Problem of using Visual Automation to force the output to be triggered
Failure to disable the admin privilege for FTP service after the ftp user’s account had been modified
Failure to list the corrupted video clips on the Remote ViewLog due to inability to repair AVI files
Failure of Dong Yang Dome (DOH-240) PTZ function
Problem of connecting the Novatel USB727 UMTS device
Incorrect Baud Rate setting used on the GPS function
Problem of achieving the defined FPS on the live video
An error message that occurred after the "Disable authentication for guest account" option was enabled on the User Account setting
Issue of OCX program update
Issue of activating the output module incorrectly during system restart in condition that the GV-Relay V2 was connected
Failure to connect to the video server through wired LAN connection after disabling the wireless LAN connection
Issue of incorrect Daylight Saving Time after the video server was restarted
Malfunction of the Ready LED which was caused by power outage during system restart.
Problem of using the Virtual I/O function in Pulse Mode on the Main System with the video server
Modified:
Settings for Video, Schedule, Time Synchronization, Input and Output to be protected when the monitoring is started.
Wired Ethernet connection to coexist with wireless Ethernet connection
